GRASS VALLEY KMV-3901 Скачать руководство пользователя страница 72

Страница: 72 / 138

System Configuration

Closing a Password-Protected XAdmin Session

Closing a Password-Protected XAdmin Session

To close your XAdmin session

1 Click

Log out

, in the navigation area on the left side of the current page, when you are

ready to close your session.

A confirmation message appears.

2 Click

The login page appears. Only authorized users have access to XAdmin for this
multiviewer.

Opening Signal Path Viewer

To open Signal Path Viewer

• Double-click the Signal Path Viewer shortcut

on your desktop.

The application automatically connects to your multiviewer, and the Signal Path Viewer
panel appears.

Note:

Should you need Signal Path Viewer to connect to a different

multiviewer, then you must install it again, from the other multiviewer’s
home page. See

Installing Signal Path Viewer

on page 51.

Содержание KMV-3901











































































































































Результаты поиска

Содержание KMV-3901

Отзывы:

GRASS VALLEY KMV-3901, Инструкция по установке и обслуживанию, Страница: 72 / 138

Результаты поиска

Содержание KMV-3901

Отзывы: