GRASS VALLEY KMV-3901 Скачать руководство пользователя страница 88

Страница: 88 / 138

System Configuration

Info Panel

Three buttons give access to additional information and controls:

Details

Reports the firmware version, service version, and panel version for this card.

Advanced

Shows the Long ID for this card. The Long ID is the address of this KMV-
3901/3911 in the iControl network.

Remote system
administration

Opens the

Joining Locators

window, which lists remote lookup services to

which this KMV-3901/3911 is registered.

• Click

Add

to force the iControl service for this KMV-3901/3911 to register

itself on a lookup service, by using the following syntax in the

Input

window:

jini://<ip_address>

where

<ip_address>

is the IP address of the server running the lookup

service.

• Select one of the services listed in the window by clicking on it, and then

click

Remove

to remove it from the list.

Содержание KMV-3901











































































































































Результаты поиска

Содержание KMV-3901

Отзывы:

GRASS VALLEY KMV-3901, Инструкция по установке и обслуживанию, Страница: 88 / 138

Результаты поиска

Содержание KMV-3901

Отзывы: