GRASS VALLEY KMV-3901 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 138

GRASS VALLEY KMV-3901 Скачать руководство пользователя страница 14

14

Installation

Optional Ancillary Equipment

• Cables (to connect your multiviewer to video sources, to displays, and to the network):

Optional Ancillary Equipment

The following optional equipment may be supplied with your order: Kaleido RCP-2 or RCP-
200 multi-function remote control panel

Cable type

Purpose

CAT-5

For Ethernet connectivity

Display cables

Either extension modules—for example Grass Valley’s DXF-200
(part number DXF-200-C)—or standard HDMI cables (non-locking)

Video cables

Standard coaxial cables with BNC connectors

Notes

• On all Kaleido multiviewers, the network adapters are set to auto-

negotiate. By default, the connection speed and duplex mode will be set
automatically based on the corresponding port settings on the switch.

• If you have two displays, make sure the HDMI connectors on the

multiviewer side have the same dimensions. Otherwise, the multiviewer’s
built-in locking mechanism will not be able to secure the smaller of the
two connectors. You may order suitable HDMI cables from Grass Valley—
HDMI to DVI female cable (1ft), part no. KXC-HDMI-DVI.

«
...
12
13
14
15
16
...
»

Содержание KMV-3901











































































































































Отзывы:

Нет отзывов