Graphite 59G020, Инструкция по эксплуатации

Страница: 9 / 64

9
TRANSLATION OF
THE ORIGINAL INSTRUCTIONS
MULTI PURPOSE TOOL
59G020
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
DETAIL SAFETY RULES (MULTI PURPOSE TOOL)
• During operation hold the tool firmly in closed hand.
• Before switching the tool on make sure it does not touch
processed material.
• Before cutting floor, wall or other surface make sure the cut area is
free from gas or electric installation. Cutting a live wire may cause
electric shock and cutting gas pipe may cause explosion.
• Do not touch moving parts of the tool.
• Do not put the tool aside before it stops completely.
• Hold the tool firmly in your hand before switching it on.
• Do not touch blade and processed material just after the work has
been finished, these pieces may be very hot and may cause burns.
• To replace blade or sanding paper, first switch the tool off with the
switch and wait until it stops working, then disconnect the tool
from mains socket.
• Prior to operation check if there is enough space under processed
material to avoid table or floor damage with the blade.
• Use anti-dust mask. Dust produced during operation is harmful
to health.
• Do not eat, drink or smoke in a room, where paint with lead
compounds is removed with this tool. There should be no
bystanders in the room. Contact with or inhalation of dusts with
lead compounds may be harmful to health.
• Before sanding connect dust extraction system to the tool.
• The tool is not designed for wet operation.
• Keep the power cord away from moving parts of the tool at all
times.
• When you see unusual behaviour of the tool, smoke or hear
strange noises, immediately switch off the tool and remove the
plug from mains socket.
• To ensure proper cooling during tool operation keep the
ventilation holes unobstructed.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always a
small risk of injuries at work.
CONSTRUCTION AND USE
Multi purpose tool is driven by single-phase motor whose rotation
is changed to oscillations. Various working tools available for the
tool allows for use in various types of tasks. This type of power tool
is widely used for: cutting wood, wood-based materials, plastics,
non-ferrous metals and joining parts (nails, bolts etc.). It can also be
used to process soft ceramic tiles, sanding and dry scraping small
surfaces. Possibility of processing abovementioned materials in
hardly accessible places and close to edges is an advantage of the
tool.
Range of use covers the following tasks: small model making,
locksmith, woodworking and any work from the scope of individual,
amateur activities (tinkering).
Use the power tool according to the manufacturer’s instructions
only.
Use the power tool only with original equipment.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1.
Sanding pad
2.
Switch
3.
Adaptor
4.
Clamp
5.
Dust extraction add-on
6.
Fixing screw with washer
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1.
Various working tips - 6 pcs
2.
Sanding paper (80#) - 5 pcs
3.
Dust extraction add-on with a clamp - 1 set
4.
Hexagonal key - 1 pce
5.
Transport case - 1 pce
PREPARATION FOR OPERATION
SELECTION OF WORKING TOOL
Below table presents examples of use for various working tools.
Name Type of material Intended use Example
HSS blade
for metal Metal (e.g. nails,
bolts, small sec-
tions), non-ferrous
metals Small dividing and
plunge cutting. Cutting narrow
sections short,
cutting joining
elements, e.g.
clamps.
H a l f - r o -
und HCS
wheel for
wood Wood, wood-based
materials, plastics Dividing and plun-
ge cutting in cor-
ners and hard to
reach areas, near
surfaces. Narrow plunge
cuts in solid
wood, e.g. for
air grates.
HCS blade
for wood Wood, wood-based
materials, plastics Dividing and plun-
ge cutting in cor-
ners and hard to
reach areas, near
surfaces. Cut outs in fur-
niture boards,
cutting cove
bases short,
plunge cutting
for fitting floor
panels.
H a l f - r o -
und wheel
with tung-
sten grit Cement joints, soft
ceramic tiles, hard
plastics and other
materials. Cutting short and
cutting off close to
edges, in corners
and hardly acces-
sible places. Removal of
joint, cutting
holes in cera-
mic tiles and
plastics.
Delta san-
ding pad Wood, wood-based
materials, abrasive
materials. Sanding in hard to
reach areas and in
corners on a hard
substrate. Removal of
mortar and
glue for ce-
ramic tiles,
sanding solid
wood, poli-
shing.
Stiff scra-
per Linings, floors, cera-
mic tiles. Scraping soft ma-
terials on a hard
substrate. Removal of
mortar resi-
dues, glue for
lining or cera-
mic tiles.
INSTALLATION AND REPLACEMENT OF SANDING PAPER
Sanding pad is equipped with hook-and-loop attachment system
for quick and easy replacement of sanding paper. Choose sanding
paper with appropriate gradation depending on the processed
material and desired level of material removal. All types of sanding
paper, abrasive cloths and polishing felt are allowed.