Change
Change
Change Drums
Drums
Drums
To prevent serious burns from dripping material,
never reach under the heated platen after the
platen is out of the drum.
Follow the procedure to change the drum on a fully
heated system.
NOTICE
NOTICE
NOTICE
Be
Be
Be sure
sure
sure to
to
to reload
reload
reload the
the
the empty
empty
empty supply
supply
supply unit
unit
unit with
with
with a
a
a full
full
full
drum
drum
drum of
of
of material
material
material immediately.
immediately.
immediately. Do not raise the ram
and remove the platen from the empty drum until
you are ready to immediately install a new drum.
Do
Do
Do not
not
not raise
raise
raise the
the
the ram
ram
ram and
and
and remove
remove
remove the
the
the platen
platen
platen from
from
from
the
the
the empty
empty
empty drum
drum
drum unless
unless
unless the
the
the supply
supply
supply unit
unit
unit is
is
is at
at
at full
full
full
operating
operating
operating temperature.
temperature.
temperature. Drum changes can only be
performed when the system is heated.
An
An
An empty
empty
empty drum
drum
drum clamp
clamp
clamp can
can
can interfere
interfere
interfere with
with
with the
the
the up
up
up
and
and
and down
down
down operation
operation
operation of
of
of the
the
the ram.
ram.
ram. When raising or
lowering the ram, make sure the drum clamp stays
clear of the platen assembly.
Do
Do
Do not
not
not use
use
use a
a
a drum
drum
drum of
of
of material
material
material that
that
that has
has
has been
been
been
dented
dented
dented or
or
or otherwise
otherwise
otherwise damaged;
damaged;
damaged; damage to the
platen wipers can result.
All
All
All systems
systems
systems include
include
include Low/Empty
Low/Empty
Low/Empty Sensors:
Sensors:
Sensors:
• The air will shutoff to prevent the pump from
cavitation. If the light tower kit is installed, a solid
red light indicates that the pail is empty and ready
to change.
• In a tandem system, a flashing red light means
that both drums are empty and the system has
shutdown.
1.
Press
to stop material tracking.
2.
Push in the air motor slider valve (CM) to stop
the pump.
3.
Set ram director valve (CC) to UP and raise the
platen (G) and immediately press and hold the
blowoff buttons (CG) until the platen is completely
out of the drum. Use minimum amount of air
pressure necessary to push the platen out of the
drum.
Excessive air pressure in the material drum
could cause the drum to rupture, causing
serious injury. The platen must be free to move
out of the drum. Never use drum blowoff air
with a damaged drum.
4.
Release the blowoff air button and allow the ram
to rise to its full height.
5.
Remove the empty drum.
6.
Inspect platen and if necessary, remove any
remaining material or material build-up.
7.
Follow steps in
, and
.
36
334130D
Содержание Therm-O-Flow 200
