Graco InvisiPac GS35 Plug-Free Скачать руководство пользователя страница 9

Страница: 9 / 34

Installation

Installation

Mounting

Mount manifold on a 1/2 in. (12 mm) diameter bar

using mounting clamp (H) to hold the gun assembly

in place and ensure adhesive is applied properly.

NOTICE

To prevent heat transferring into other components

of the packaging line, ensure that the insulator is

installed.

1. Use a 5 mm Allen wrench to loosen the mounting

clamp and slide the gun assembly on the

mounting bar.

2. Tighten the mounting clamp.

Note

Provide enough room to access sides of

applicator for maintenance and repair.

Figure 3 Mounting Clamp

Connect Heated Hose

1. Connect the hose ﬂuid outlet to the manifold ﬂuid

inlet (E). Use two 11/16 in. wrenches to tighten

the hose ﬁtting.

Figure 4 Connect the Heated Hose

2. Connect the cordset (M) to the hose.
3. Connect the hose inlet to the melter system

outlet. See the heated hose manual for

installation guidelines.

4. Connect the hose cordset to melter. See the

heated hose manual for installation guidelines.

Connect Solenoid Valve

1. Connect 3/8 in. diameter air supply tubing to a

clean, dry, and non-lubricated air supply and to

the push-to-connect air inlet ﬁtting (L).

Figure 5 Air Inlet Fitting

2. Connect solenoid valve to 24 VDC or 110 VAC

signal. See

Connect Triggering Device, page 10

For applicators without a supplied solenoid valve:
• Use solenoid valves with an override switch.
• Ensure that your solenoid valve is connected to the

manifold with tubing rated for 400°F(204°C).

• Ensure the solenoid valve is rated for

high-temperature applications.

3A2805B

Содержание InvisiPac GS35 Plug-Free



































Результаты поиска

Содержание InvisiPac GS35 Plug-Free

Отзывы:

Похожие инструкции для InvisiPac GS35 Plug-Free

Бренды по названию

Популярные бренды

Graco InvisiPac GS35 Plug-Free, Инструкция - Каталог запасных частей

Результаты поиска

Содержание InvisiPac GS35 Plug-Free

Отзывы:

Похожие инструкции для InvisiPac GS35 Plug-Free

Бренды по названию

Популярные бренды