Graco HFRL Скачать руководство пользователя страница 85

Страница: 85 / 142

Appendix D - ADM Error Codes

3A2175Z

A4N1 Motor Over

Current

A hardware current fault has

occurred causing a system

shutdown

Alarm

Short circuit of motor

wiring

Check wiring to the motor to ensure no bare wires

are touching and that no wires are shorted to ground

Motor rotor has become

locked

Unplug the directional valve (so pressure will not

build) and try to move the motor again. If this

succeeds then the power pack may need to be

replaced. If the motor is still unable to move, the

bearings or hydraulic pump have likely failed in the

motor and will need to be replaced.

A7A6 Red Blanket

Control Fault

Unexpected current to

heater/chiller

Alarm

Shorted Temperature

Control Module

If temperature rises for a zone that has been

disabled, replace Temperature Control Module

A7B5 Blue Blanket

Control Fault

A7A3 Red Inline

Control Fault

A7B1 Blue Inline

Control Fault

A7A2 Red Hose

Control Fault

A7B4 Blue Hose

Control Fault

A7A7 Red Chiller

Control Fault

A7B8 Blue Chiller

Control Fault

A8A6

No Red

Blanket

Current

No current to the conditioning

zone

Alarm

Tripped circuit breaker Visually check circuit breaker for a tripped condition

A8B5

No Blue

Blanket

Current

A8A3 No Red Inline

Current

A8B1 No Blue Inline

Current

A8A2 No Red Hose

Current

A8B4 No Blue Hose

Current

Low power

Measure voltage across input terminals on power line

filter. Voltage should measure between 190 and 264

Vac

A8B7

No Red

Chiller

Current

Cable unplugged/loose

power

Check for loose or disconnected wires or plugs

A8B8

No Blue

Chiller

Current

Bad heater(s)

Measure resistance of heater(s)

A9C1 Motor Over

Current

A software error has occurred

commanding too much

current

Alarm

Bad Motor Control

Module code

Check for MCM software update, load latest MCM

software, if problem persists contact Graco

B9C0

Small Shot

Request

The requested dispense

amount is below the minimum

amount of the system (25% of

the combined pump volumes

is the minimum)

Deviation

Pumps are defined with

the wrong size

On the ADM go into the Setup screens to the System

screens then make sure that the pump sizes are

defined correctly

Requested shot is below

the capabilities of the

current pump setup

If the user has to be able to take the shot the system

must be fitted with smaller pumps

B9C1

The requested dispense
amount (time/volume/weight)
is below the minimum amount
of the system

Short shot size

Increase the time/volume/weight of the shot

Error

Code Error Name Error Description

Error

Type

Cause

Solution

Содержание HFRL















































































































































Результаты поиска

Содержание HFRL

Отзывы:

Похожие инструкции для HFRL

Бренды по названию

Популярные бренды

Graco HFRL, Руководство по установке и эксплуатации

Результаты поиска

Содержание HFRL

Отзывы:

Похожие инструкции для HFRL

Бренды по названию

Популярные бренды