Graco HFRL Скачать руководство пользователя страница 32

Страница: 32 / 142

Setup

3A2175Z

4. Assemble and Connect regulator assemblies (If

Equipped).

NOTE:

Systems equipped with a fluid regulator on the

material inlet will be provided with necessary parts to

assemble the regulator. Refer to repair-parts manual for

assembly illustrations.

a. Attach the male nipple located on the regulator

assembly to the female swivel located on the

end of the pump assembly.

b. Connect the air tube to the tee fitting on the

power valve assembly located on the right side

of the machine.

5. Connect feed pumps (HFRL).

a. Install feed pumps for component A (Red) and

B (Blue) supply drums. See

. 1

and

. 4

pages

and

NOTE:

A minimum feed pressure of 50 psi (0.35 MPa,

3.5 bar) is required at both feed inlet pressure gauges

(FP). Maintain A (Red) and B (Blue) feed pressures

within 10% of each other.

b. Ensure A (Red) and B (Blue) inlet valves (FV) are

closed.

c. Adjust the fluid pressure regulator so the pres

sure gauge reads zero.

NOTE:

Supply hoses from feed pumps should be 3/4

in. (19 mm) ID minimum.

d. Assemble, connect and tighten component

B (Blue) inlet hose to the 3/4 npt(f) swivel on the

component B (Blue) inlet assembly. Refer to

repair-parts manual for assembly illustrations

e. Assemble, connect and tighten component

A (Red) inlet hose to the 3/4 NPT(f) swivel on

the component A (Red) inlet assembly. Refer to

repair-parts manual for assembly illustrations.

pressure

ti18216a

gauge

250 psi max inlet

pressure

3000 psi max

inlet pressure

ti9883a1

ti18217a

Содержание HFRL















































































































































Результаты поиска

Содержание HFRL

Отзывы:

Похожие инструкции для HFRL

Бренды по названию

Популярные бренды

Graco HFRL, Руководство по установке и эксплуатации

Результаты поиска

Содержание HFRL

Отзывы:

Похожие инструкции для HFRL

Бренды по названию

Популярные бренды