Graco 17H466 Скачать руководство пользователя

Страница: 11 / 72

Ground Drive Belt Replacement

3A3394E Repair - Parts

Ground Drive Belt
Replacement

Removal

1. If equipped with a Pressurized Bead System,

remove pressurized bead tanks and compressor,
see Pressurized Bead System manual 332230.

2. Loosen four screws and remove belt cover.

3. Loosen two hold-down bolts.

4. Loosen tension bolt to bring two pulleys closer

together to create slack in the belt.

5. Remove belt.

Installation

1. Install belt onto pulleys.

2. Tighten tensioning bolt to move two pulleys apart

and tighten belt to proper tension (see table).

3. Install mounting plate and tighten two hold-down

bolts.

4. Replace belt cover and tighten four screws.

5. If equipped with a Pressurized Bead System, install

pressurized bead tanks and compressor, see Pres-
surized Bead System manual 332230.

ti19128a

ti19130a

ti19131a

ti19133a

Ground Drive Belt Tension Recommendations

New Belt

Tension

53 +/- 2 Lbf (236 +/- 9 N)

Frequency

167 +/- 3 Hz

Used Belt

Tension

45 +/- 2 Lbf (200 +/- 9 N)

Frequency

155 +/- 3 Hz

Gates Sonic Tension Meter
Settings: M = MASS = 85 g/m

W = # of belts = 1
S = Span = 157 mm

ti19134a

ti19132a

ti19129a

ti19128a

Содержание 17H466









































































Результаты поиска

Содержание 17H466

Отзывы:

Похожие инструкции для 17H466

Бренды по названию

Популярные бренды

Graco 17H466, Запасные части

Результаты поиска

Содержание 17H466

Отзывы:

Похожие инструкции для 17H466

Бренды по названию

Популярные бренды