Graco 17H466 Скачать руководство пользователя

Страница: 28 / 72

Engine Replacement

3A3394E Repair - Parts

Installation

1. Install engine voltage regulator below engine

mounting plate with two screws. Connect regulator
to wire harness.

2. Install engine and tighten four mounting bolts and

nuts.

3. Install choke cable:

a. Make sure choke knob is pressed down.

b. Insert choke cable wire into hex-shaped pivot.

c. Insert cable sheathing under cable clamp and

tighten screw.

d. Tighten screw on hex-shaped pivot.

e. Verify proper operation of engine choke.

4. Install throttle cable.

a. Place speed lever to high speed.

b. Insert “Z” bend wire into hole furthest from pivot.

c. Place cable sheathing under clamp and pull

cable against high speed stop screw.

d. Tighten screw on cable clamp.

e. Verify proper operation of speed lever.

5. Install air filter base, element and cover.

6. Connect seven wires to engine.

7. Install clutch, see

Clutch Replacement

, page 24.

8. Connect two negative (black) wires at battery.

9. Add gas and oil to engine (see Operation manual).

10. Start engine and verify high speed of 3600 rpm.

ti19706a

ti19187a

ti19686a

ti19690a

ti19186a

Engine Ground

Voltage Regulator

Ignition

Starter Solenoid

Battery

ti23921

Содержание 17H466









































































Результаты поиска

Содержание 17H466

Отзывы:

Похожие инструкции для 17H466

Бренды по названию

Популярные бренды

Graco 17H466, Запасные части

Результаты поиска

Содержание 17H466

Отзывы:

Похожие инструкции для 17H466

Бренды по названию

Популярные бренды