Graco 17H466 Скачать руководство пользователя

Страница: 42 / 72

Rear Wheel and Wheel Motors

3A3394E Repair - Parts

Rear Wheel and Wheel Motors

Rear Wheel Removal

1. Set LineStriper on blocks so wheels are off ground.

2. Remove four lug nuts (22) and wheel (16).

Rear Wheel Installation

1. Replace wheel and install lug nuts. Alternately

tighten lug nuts opposite of each other.

2. Tilt LineStriper on side and remove blocks.

3. Inflate rear tires to 55 +/- 5 psi (380 +/- 34 kPa).

Wheel Motor Removal

1. Place jack under frame near wheel and raise jack.

2. Remove four lug nuts (22) and wheel (16).

3. Remove pin (56), castle nut (21b) and wheel hub

(22b). Wheel hub may require a wheel puller; not
supplied by Graco.

4. Remove screw (6) and distance sensor (4) with

clamp (5).

5. Remove four bolts (78), lock nuts (79) from fender

(19).

6. Disconnect two hydraulic hoses (112) from wheel

motor (21a) and remove wheel motor.

ti18587a

ti18589a

ti18588a

ti18589a

ti23945a

22b

21b

21a

112

Содержание 17H466









































































Результаты поиска

Содержание 17H466

Отзывы:

Похожие инструкции для 17H466

Бренды по названию

Популярные бренды

Graco 17H466, Запасные части

Результаты поиска

Содержание 17H466

Отзывы:

Похожие инструкции для 17H466

Бренды по названию

Популярные бренды