Graco 17H466 Скачать руководство пользователя страница 31

Страница: 31 / 72

Control Board Replacement

3A3394E Repair - Parts

7. Remove two screws and splash shield.

8. Disconnect all wires from control board.

9. Remove eight control board mounting screws and

then remove control board.

Installation

1. Install control board with eight mounting screws.

2. Before connecting wires to control board, make sure

that all wires are routed above the two steering
cables.

3. Connect all wires to control board. See,

Wiring Dia-

gram

, page 68. Pump number 1 is on the left when

you stand in the operator position.

4. Bundle and secure wires with a cable tie just

inboard of the choke cable.

5. Bundle and secure wires with a cable tie just out-

board of the key switch.

6. Install fuse, see

Fuse Replacement

, page 34.

Check control, switches and display.

7. Install splash shield with two screws.

8. Install control shroud with six screws. See

Removal

step 6.

9. Install pad and tighten four screws.

ti24973a

ti24074a

ti24075a

ti2376a

ti23930a

Содержание 17H466









































































Результаты поиска

Содержание 17H466

Отзывы:

Бренды по названию

Популярные бренды

Graco 17H466, Запасные части

Результаты поиска

Содержание 17H466

Отзывы:

Бренды по названию

Популярные бренды