Gorilla Playsets Savannah II 1500FT Скачать руководство пользователя страница 74

Страница: 74 / 123

DETAIL B

TARP

FASTEN OUTSIDE GROMMETS FIRST TO

THE SIDE OF THE TARP BOARD ON

EACH SIDE WITH #14 X 1-1/4"

PAN HEAD SCREWS AND 1/4" WASHERS.

REPEAT FOR OTHER SIDE.

THEN FOLD

THIS TAB UNDER

THE TARP BOARD

AND SECURE IT TO

THE BOTTOM

SIDE OF THE TARP

BOARD WITH

#14 X 1-1/4"

PAN HEAD SCREWS

AND 1/4" WASHERS.

REPEAT FOR OTHER SIDE.

NOTE: IF YOU WISH

YOU MAY DRILL

1/8" PILOT HOLES IN THE

TARP BOARD FOR THE

PAN HEAD SCREWS.

STEP 30: TARP

1: PLACE THE TARP ACROSS THE TARP BOARDS WITH THE HEMS ON THE INSIDE.

2: FASTEN THE OUTSIDE CORNERS OF THE TARP TO THE SIDE OF THE TARP BOARD FIRST. ATTACH THE

GROMMETS IN THE TARP TO THE TARP BOARD WITH #14 X 1-1/4" PAN HEAD SCREWS WITH 1/4" WASHERS.

REPEAT FOR OTHER SIDE.

(NOTE IF YOU WISH YOU MAY PREDRILL HOLES FOR THE PAN HEAD SCREW WITH A 1/8" DRILL BIT.)

3: NOW FOLD THE FLAP UNDER THE TARP BOARD AND FASTEN THE GROMMETS UNDER THE TARP BOARD

WITH #14 X 1-1/4" PAN HEAD SCREWS WITH 1/4" WASHERS. REPEAT FOR OTHER SIDE. ( NOTE IF YOU WISH

YOU MAY PREDRILL HOLES FOR THE PAN HEAD SCREWS WITH A 1/8" DRILL BIT.)

Содержание Savannah II 1500FT




























































































































Результаты поиска

Содержание Savannah II 1500FT

Отзывы:

Похожие инструкции для Savannah II 1500FT

Бренды по названию

Популярные бренды

Gorilla Playsets Savannah II 1500FT, Руководство пользователя

Результаты поиска

Содержание Savannah II 1500FT

Отзывы:

Похожие инструкции для Savannah II 1500FT

Бренды по названию

Популярные бренды