Gorilla Playsets Savannah II 1500FT Скачать руководство пользователя страница 54

Страница: 54 / 123

STEP 10: CENTER DECK SUPPORT

1: FIND THE 2 X 4 X 70" CENTER DECK SUPPORT WITHOUT HOLES.

2: FROM THE UNDERSIDE OF THE DECK SPACERS THAT WERE PREVIOUSLY INSTALLED, PLACE THE CENTER

DECK SUPPORT AT THE CENTER OF THE DECK SPACERS (USE THE HOLE ON CENTER AS A GUIDE) AND MAKE

A MARK ON THE OUTSIDE OF THE FORT TO REPRESENT A CENTER LINE.

3: USE 2" WOOD SCREWS TO ATTACH THE DECK SPACERS TO THE CENTER DECK SUPPORT.

4: CENTER THE 2 X 4 X 70" CENTER DECK SUPPORT ON THESE MARKS AND PUSH THE CENTER DECK SUPPORT

FLUSH TO THE BOTTOM SIDE OF THE DECK BOARDS.

5: USING TWO 2-1/2" WOOD SCREWS, INSTALL THE 2 X 4 X 70" CENTER DECK SUPPORT THROUGH THE

OUTSIDE OF THE 2 X 6, AND INTO THE END OF THE CENTER DECK SUPPORT. REPEAT THIS STEP ON THE

OPPOSITE END OF THE FORT.

USE 2-1/2"

WOOD SCREWS

IN THESE LOCATIONS

ON EACH SIDE.

2" WOOD SCREW

NOTE: 2 X 4 X 47-1/2" END PANEL BOARD

REMOVED FOR CLARITY.

DETAIL B

2" WOOD SCREW

2 X 4 X 70"

CENTER DECK SUPPORT

Содержание Savannah II 1500FT




























































































































Результаты поиска

Содержание Savannah II 1500FT

Отзывы:

Похожие инструкции для Savannah II 1500FT

Бренды по названию

Популярные бренды

Gorilla Playsets Savannah II 1500FT, Руководство пользователя

Результаты поиска

Содержание Savannah II 1500FT

Отзывы:

Похожие инструкции для Savannah II 1500FT

Бренды по названию

Популярные бренды