Gorilla Playsets 1500GWF Скачать руководство пользователя страница 60

Страница: 60 / 177

STEP 5: FRONT FRAME ASSEMBLY

1: PLACE THE 2 X 6 X 102" ROPE LADDER RUNNER ON THE FRONT OF THE CORNER POSTS. THE HOLES IN THE

ROPE LADDER RUNNER SHOULD BE OFFSET UP.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE ROPE LADDER RUNNER

TO THE T-NUTS INSTALLED IN THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

3: PLACE THE 2 X 6 X 70" FRONT FACE BOARD WITH NOTCHES ON THE FRONT OF THE CORNER POSTS. THE HOLES

IN THE FRONT FACE BOARD SHOULD BE OFFSET UP.

4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE FRONT FACE BOARD TO

THE T-NUTS INSTALLED IN THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

5: PLACE THE 2 X 6 X 102" ROPE LADDER SUPPORT ON THE FRONT OF THE CORNER POSTS. THE HOLES IN THE

ROPE LADDER SUPPORT SHOULD BE OFFSET UP.

6: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE ROPE LADDER SUPPORT

TO THE T-NUTS INSTALLED IN THE CORNER POSTS.

RUNNER

BOARD

5/16" WASHER

2 X 6 X 102"

FRONT FACE

5/16 X 4-1/2"

HEX BOLT

ROPE LADDER

FRONT OF FORT

2 X 6 X 70"

RIGHT SIDE

OF FORT

2 X 6 X 102"

ROPE LADDER

SUPPORT

Содержание 1500GWF


















































































































































































Результаты поиска

Содержание 1500GWF

Отзывы:

Похожие инструкции для 1500GWF

Бренды по названию

Популярные бренды

Gorilla Playsets 1500GWF, Руководство пользователя

Результаты поиска

Содержание 1500GWF

Отзывы:

Похожие инструкции для 1500GWF

Бренды по названию

Популярные бренды