Instructions for use and installation
12
•
Never use aggressive cleaners, like polishing agents, dish
cleaning accessories, corrosion inhibitors, or any other
devices that might cause scratches.
•
Coated, stainless steel or zinc-coated surfaces or aluminum
parts must not come into contact with oven sprays, since
they might cause damage or discoloration. Oven bottom
should be removed, thoroughly cleaned and reinserted after
cleaning.
•
Never clean the oven burner yourself. This should be done
by the authorized person only. Cleaning will be required
when the flame no longer escapes from all burner nozzles.
•
When purchasing cleaning agents remember the
environment, and strictly follow the manufacturer's
instructions.
Removing wire guides
Wire guides may be removed to facilitate the cleaning of the
oven. Side grids are removed by swinging the bottom side
inwards and unhooking them from their place. Clean them only
with conventional detergents.
To reinsert, repeat the procedure backwards: slide them into
the holes and swing downwards.
Oven drawer
(certain models only)
The oven drawer is protected from accidental opening.
It may be open by lifting upwards. To remove the drawer from
the cooker pull it out to the limit, then lift upwards and pull out
completely.
Never place any flammable, explosive, or temperature non-
resistant substances or objects in the drawer.
Certain types of cookers require the rear bottom drawer slide to
be inserted into the drawer guide and pushed inside.
The drawer may also be equipped with wheel side slides. To
insert this type of drawer, slide the wheels into the slide guides
and push inwards.
Removing oven door
(certain models only)
Open the door to the horizontal position. Pull the bottom hinge
supports upwards to the vertical position and lock them to the
latch of upper hinge support. Close the door halfway (see fig.)
and pull it out.
For reinserting the door repeat the procedure backwards. Insert
the door in half open position (at an angle of 60
°
) by pushing
them all the way in during opening. Be sure that the notches on
bottom hinge carriers fit exactly the oven bottom. Now open the
door completely, remove the hinge clamps from the upper
hinge latches and return them into the horizontal position.
1
door hinge in
operating position
2
door hinge during
dismantling
Removing oven door with a single axe hinge
(certain models only)
Open the door completely and turn the removable hinge locks
backwards (see fig). Then close the door slowly and let the
locks fit to the notches. At an angle of about 15
°
lift the door
slightly up and pull the door from the hinge supports (fig. 2).
For reinserting the door repeat the procedure backwards. Insert
the door at an angle of about 15
°
into the hinge supports by
pushing them forward and downwards, so the hinges lock into
their slots (fig. 3). Check if the hinges are locked into their
respective slots.
Now open the door completely and turn the removable locks
into their original position. Close the door slowly and check if
they close properly (fig. 4). If you have trouble closing the door,
check if the hinges are properly inserted into their slots.
Attention
! Never let the hinge locks spring out, as the springs
are strong and may cause injuries.
Accessories
Accessories, like baking tray, oven grid, etc. are cleaned with
hot water and the usual detergent.
Avoid cleaning
the aluminum baking pan
with aggressive
cleaners causing scratches. The pan surface will lose its shine
with time. This is unavoidable, and does not affect your baking
results.
Special enamel
Oven interior and door lining are coated with special enamel,
with smooth and resistant surface.
This special coating facilitates cleaning at room temperature.
Troubleshooting guide
•
Any unskilled attempt to repair the appliance is extremely
dangerous as it might cause electric shock and short circuit.
To avoid such injuries any repairs may be performed only by
qualified personnel, or after sales service.
•
Before attempting any repairs disconnect the appliance from
the mains by removing the fuse or unplugging the mains
lead from the mains socket.
Note!
There are, however, some minor faults which may be easily
removed by the user, in accordance with the instructions that
follow.
