90
SAFETY PRECAUTIONS
SYSTEM OPERATION
O
w
w
w
w
O
O
With monitor, telephones and distributor:
Do not use excessive force when tightening the connector screws
Remenber, the installation and handling of these equipments must be performed by authorised
personnel and in the absence of electrical current.
Do always follow the enclosed information.
.
Install the equipments in a dry and protected place without risk of drip or water projections.
Avoid to place it near to heating sources, in dusty locations or smoky enviroments.
Do not block ventilation holes of the equipments so that air can circulate freely.
O
O
O
O
O
O
: a
.
.
.
i
.
.
.
.
.
.
.
:
.
To make a call the visitor should press the push button corresponding to the apartment he wishes to
contact n acoustic tone will be heard confirming the call is in progress once the push button has
been pressed At this moment the call will be received at the monitor (telephone) in the dwelling
During the call the visitor can correct his call by pressing a push button corresponding to a different
apartment, in which case the original call is cancelled
In systems with several access doors, the other door panel(s) will be automatically disconnected: f a
visitor tries to call from other door panel an acoustic tone will be heard confirming the system is busy
The call tone will be reproduced on the monitor during 3 seconds: after this time the picture will
appear on the master monitor without the visitor being aware of this To see the image on a slave
monitor pick up its handset, dissapering the image on the other monitor If the call is not answered in
45 seconds, the system will be freed
To establish communication pick up the monitor (telephone) handset
The communication will last for one and a half minutes or until the handset is replaced Once the
communication has finished the system will be freed
To open the door, press the door release push button during call or communication progresses with
one press, the door release operates during 3 seconds
Coming from previous page
SYSTEM CHARACTERISTICS
O
O
O
O
O
O
O
O
w
w
w
w
O
Video door entry system with simple installation specially-designed to replace 4+n audio door entry
systems. Installation is done through 5 common wires
Up to 6 door (access) panels which do not need switching units
Up to 200 terminals (monitors and telephones) for installation without using converters
Up to 132 apartments with door panels of push buttons and up to 200 apartments with coded panels
(requires the use of the digital converter
Acoustic busy channel and call acknowledgement signals
Door opening timed at 3 seconds
A.C. or D.C. lock release operated through a relay
With telephones T-730/R5
Completely private conversation
Output for connection to call repeater
Up to 1 additional monitor or telephone per apartment (installation of an additional monitor
requires a supplementary power supply in the landing, see page 125-126)
Does NOT require batteries for operation
With monitors Tekna R5, in addition to the above features
Privacy on audio and video communications
'Video-Spy' function with the communication channel remaining free
without independent call lines
.
.
.
).
.
.
.
:
.
.
.
.
:
.
.
Colour screen.
CD-PLUS/R5
w
w
w
89
INTRODUCTION
INDEX
SAFETY PRECAUTIONS
First of all we would like to thank and congratulate you for the purchase of this product manufactured by
Golmar.
The commitment to reach the satisfaction of our customers is stated through the ISO-9001 certification
and for the manufacturing of products like this one.
Its advanced technology and exacting quality control will do that customers and users enjoy with the
legion of features this system offers. To obtain the maximum profit of these features and a properly wired
installation, we kindly recommend you to expend a few minutes of your time to read this manual.
O
O
O
O
w
w
w
w
w
w
Install or modify the equipment
.
The installation and handling of these equipments must be performed by
.
The entire installation must be at least
. away from any
.
With power supply:
Do not use excessive force when tightening the connector screws.
Install the power supply in a dry and protected place without risk of drip or water projections.
Avoid to place it near to heating sources, in dusty locations or smoky enviroments.
Do not block ventilation holes of the unit so that air can circulate freely.
To avoid damage, the power supply has to be firmly fixed.
To avoid an electrical shock, neither remove the protection cover nor handle the connected wire
in the terminals.
without the power connected
authorised personnel
other installation
40 cm
Introduction ...........................................89
Index.....................................................89
Safety precautions .............................89-90
Systems characteristics.............................90
System operation ....................................90
Definition...............................................91
Minimum requirements............................91
Door panel description ............................92
Modules description....................................
Sound modules EL631-R5/EL640-R5 .....93
Push buttons module EL610D.................94
Door panel ................................................
Embedding box positioning ...................95
Embedding box installation ..............95-96
Assembly electronic modules .................96
Hold the frame .....................................97
Push buttons connection...................97-98
Push buttons coding..............................98
Sound module configuration..................99
Final adjustments ...............................100
Close the frame..................................100
Place the nameplate labels ..................100
Door panel assembly ..........................101
Close the door panel...........................101
Power supply & lock release installation....102
Tekna R5 monitor ........................................
Description & function push buttons ......103
End of line resistor...............................104
Monitor connector description .............105
Monitor installation.............................106
Programming.....................................107
T-730/R5 telephone....................................
Description........................................108
Function push buttons .........................108
Telephone installation .........................109
Programming.....................................110
Installation.................................................
Door panel.................................111-112
Power supply and lock release ..............113
Reassignment of conductors ................114
Floor distribution.........................115-116
Installation diagrams with D4L-R5 .................
Video sys. with d.c. lock release ............117
Video sys. with a.c. lock release/TF104 ..119
Installation diagrams with D4L-R5R ...............
Video sys. with d.c lock release .............121
Installation diagram Audio system ...........123
Optional connections ....................125-129
Troubleshooting hints ............................130
Compliance.........................................131
Continue
