manualshive.com logo in svg

Goldacres Windrow MY18 2500L, Руководство оператора, Страница: 23 / 74

Поделиться
Скачать
Goldacres Windrow MY18 2500L Скачать руководство пользователя страница 23

Chapter 6 - Calibration -

 17

Windrow 2500L Operator’s Manual MY18 - REV 1

INITIAL CONSOLE PROGRAMMING

After the console has been installed and turned on it 
will require a one-time initial programming. For more 
detailed information about console features and 
operation consult the Raven SCS 450 Installation and 
Service manual.

STEP 1: 

Unit of measure options will be displayed. 

Set your unit of measure by pressing [CE] repeatedly 
until the desired unit is displayed (SI is the metric 
unit in volume per hectare) and then press [ENTER].

STEP 2: 

Now choose your speed sensor type by 

pressing [CE] repeatedly to cycle the two options 
and then press [ENTER].

SP 1 - Wheel-Drive or Drive-Shaft Speed Sensor

SP 2 - Radar Speed Sensor

STEP 3: 

The console will now ask for the valve type. 

Press [ENTER] to accept ‘C-SD-Standard Valve’ for 
this sprayer.

IMPORTANT: 

Steps 1-3 are very important because 

the system will appear to function properly but 
if the units are incorrect, the quantities will be 
very inaccurate. If an error has been made whilst 
calibrating these 2 steps, turn the console off then 
turn back on again while holding [CE] to reset and 
clear all memory. To see what has been programmed, 
press and hold [SELF TEST] for about 5 seconds until 

the programmed information is displayed (flashing 

and toggling).

STEP 4: 

Press [BOOM CAL] then [ENTER]. Enter 

boom section 1 width in centimeters and press 
[ENTER].

e.g. 6 m = 600 cm. Press [6] , [0] , [0].

The Raven 450 console has provisions for handling 
up to 5 boom sections. To measure the boom width 
for each boom section, count the number of nozzles 
in each section and multiply by the nozzle spacing. i.e. 
12 nozzles in one section at 50 cm (0.5 m) spacings 
becomes 12 x 0.5 m = 6 metres.

STEP 5: 

Press [1] (up arrow) to select boom section 

2 (B-02) Enter section width in centimeters and then 
press [ENTER].

STEP 6: 

Enter values for remaining boom sections 

using [1] (up arrow) and [2] (down arrow) to select 
them. If a boom section is not needed, enter the 
width value as ‘0’.

STEP 7: 

 Press [SPEED CAL] then [ENTER]. Enter 

speed CAL in decimeters e.g. 477 (1 metre = 10 
decimeters) then press [ENTER]. 

Speed CAL is the distance measured by 10 
revolutions of the speed sensor wheel. This is best 
done with the tank half full of water which best 
simulates average wheel diameter between full and 
empty loading and measured on ground that is 
typical to what will be encountered when spraying. 
Also note the tyre pressure when this procedure 
is performed. This tyre pressure needs to be 
maintained for the speed CAL to be accurate. The 
speed CAL should be checked at the start of every 
spraying season as the speed CAL may need to be 
altered to compensate for tyre wear, etc.

NOTE: 

For SCS450 console with 4 wheel magnets 

(2 red and 2 black) - use the measured distance 
converted to decimeters for the speed CAL entry 
(1 metre = 10 decimeters).

For SCS450 console with 2 wheel magnets (1 red 
and 1 black) - use the measured distance converted 
to decimeters and then multiplied by 2 for the speed 
CAL entry (1 metre = 10 decimeters).

STEP 8: 

Press [METER CAL] then [ENTER] 

Enter Meter Cal for litres. Press [ENTER] (e.g. 185) 
Meter Cal is the Calibration number on the Flow 
Meter white tag. The required number for litres is the 
number in square brackets.

STEP 9: 

 

Press [VALVE CAL] then [ENTER]   
Enter ‘2123’  
Press [ENTER]

STEP 10: 

Press [RATE 1] then [ENTER] 

 

Enter Rate 1 in litres per hectare e.g. 60. 
Press [ENTER]

STEP 11: 

Press [RATE 2] then [ENTER] 

 

Enter Rate 2 in litres per hectare e.g. 75. 
Press [ENTER]

NOTE: 

RATE 2 can be the same as RATE 1 if only 

one rate is to be used.

Auto Rate Control Calibration - Raven SCS 450

Continued over page

Содержание Windrow MY18 2500L











































































Отзывы:

Нет отзывов