background image

 

 

Global Fire Equipment // 

globalfire.pt 

ma_oexv2_01_010001_en_180730

 

 
 

ORION-EX V2 

Conventional Fire Detection & Extinguishing Panel 

 

INSTALLATION, OPERATION & MAINTENANCE MANUAL

 

 

 

GENERAL DESCRIPTION 

 

The ORION-EX Conventional Fire Detection and Extinguishing Panel is designed and manufactured to comply with 
EN54-2, EN54-4 and EN12094-1 standards. 

 
Advanced configuration solutions include the following: programmable pre-release and extinguishing times, electro valve and 
flow pressure switch status indications; start and abort remote activation; four fire detection zones causing different effects. 
Finally all inputs are fully monitored for both Fire, Activation and Fault Conditions.  
 

MAIN FEATURES 

Fire Detection Zones: 2 crossed Zones and 1 individual Zone linked with automatic extinguishing cycle. One 

dedicated Zone only for fire detection which doesn’t start automatic extinguishing cycle 

Up to 32 conventional devices (smoke and/or heat detectors and call-points) per zone 

Active End of Line for Zone wiring monitoring (10uF/50V bipolar capacitor) 

Programmable Pre-Release and Extinguishing times 

Monitored inputs for Manual Extinguishing Cycle Activation and Remote Abort 

Electrovalve solenoid and Weight/Flow/Pressure Switch Status monitoring 

One man test capability 

Supervised auxiliary 24-volt supply output 

3 Supervised/monitored output circuits 

1 Remote reset input 

2 Relay outputs for fire and fault status indication 

Dedicated repeater panel and analogue loop interface 

Additional output via MPX-REL & MPX-SNDR modules 

Fully EN54-2, EN54-4 and EN12094-1 compliant. 

 

IMPORTANT SAFETY NOTES 

 
● This equipment must only be installed and maintained by a suitably qualified and technically competent person. 
● This equipment must have an Earth Connection. 
● A basic knowledge and training in the installation of Fire and Extinguish Detection systems is assumed. 
● The Fire Detection system should be designed by a suitably qualified person with reference to the Local 

Regulations and Guidance from the fire Officer where applicable. 

 

Содержание ORION-EX V2






















Отзывы: