background image

 

 

Page 2 of 14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Girard Systems awnings may be operated in light wind and rain 

conditions.  When periods of heavy rain and or high wind are expected 

the awning must be closed. Never leave the awning open and 

unattended. 

Damage caused by wind and rain is not covered by warranty. 

 

All awnings must be closed prior to moving the vehicle for any reason. 

As an extra safety precaution a visual check that every awning is fully 

closed is required. 

Damage caused by failure to comply with these instructions is 

not covered by warranty

 

Before using your awning, ensure that the area into which the awning 
will be deployed is free of obstructions (Trees, walls, pillars, posts, 
other vehicles etc.) 
Damage caused by collisions with any of the above or similar is 
not covered by warranty. 
  
Before using your awning make sure that all of your electrical circuits 
are operating correctly. Recreational Vehicles can generate AC power 
from three separate sources. The electrical system transfer switch in 
your vehicle will select power for the awning as follows: 
 

Shore Power – if connected; 
Generator Power – if the generator is running; 
Inverter Power – batteries must be charged for inverter operation. 
 

Girard Systems awnings are supplied with an electric motor appropriate to the 

product.

 

 

Содержание GC1146C















Отзывы: