GILGEN doorboy DBL-W, Руководство по сборке и эксплуатации

Страница: 14 / 31

0552-999-03_05.98.p65
4-4
33
90°
max. 150 N
Fig. 10
Modification reserved
Dimensions in mm
Checking the closing force
According to the FCOS-regulations 1511, the force on the closing
edge of the door must be limited to 150 N.
- Close the door via an impulse transmitter and manually stop it
during the closing procedure. With an applied force of max.
150 N, the drive unit shall reopen. Diagrammic arrangement for
measuring this force by means of a spring balance (33) according
to Fig. 10.
- Should the required stopping force exceed 150 N, a readjustment
must be made by means of the BEDIS.
Status displays on the control unit
On the control LED D31 to D34
• D31 (green)
An opening or closing command is pending.
• D32 (green) A stopping command is pending.
• D33 (green) A reversing command is pending.
• D34 (red) System error. The specialists can carry out a
detailed error analysis by means of the BEDIS.
Functional and operating instructions
The Gilgen drive unit for overhead doors can be operated by impulse
transmitters such as remote radio control, key-operated switch or
external push-buttons. Only a short impulse is required.
Step-by-step function OPEN-STOP-CLOSE:
The door is closed:
A single impulse opens the door.
The door is open:
A single impulse closes the door.
The door is in motion:
A single impulse stops the door.
A further impulse causes the door to reverse its movement.
Safety mechanism:
Neither persons nor objects are supposed to stay within the pivoting
range of the door leaf. Should this rule inadvertently not be followed,
the control of the drive unit is designed for the following safety
function: As soon as the door leaf meets an obstacle during the
closing procedure, its movement is reversed (this function can be
changed to STOP with autorelease by means of the BEDIS). Should
the door encounter an obstacle during the opening procedure, the
drive unit automatically stops and the door is shortly reversed. The
next impulse causes the door to close.
If the pivoting range of the door is monitored by external safety ele-
ments (such as photoelectric cells, contact sills etc.), a closing door is
immediately reversed as soon as the presence of a person or an
object is detected within the monitoring range of the safety element.
Emergency unlocking:
In the event of a power failure or other malfunctions, the door can be
unlocked from the outside by turning the door handle or from the
inside by pulling the red knob. This causes the sliding carriage to be
separated from the drive chain. Now the door can be easily opened by
hand. As soon as the cause of the malfunction has been eliminated or
the power supply been restored, the chain automati-cally enters the
sliding carriage when an impulse is given and the door is opened.
Illumination:
The drive unit is supplied with a built-in socket E14-230 V and an
incandescent candle lamp 25 W.
The illumination is switched on when the opening impulse is given and
switched off after approx. 180 sec.
Appendix
Diagram ............................................................................. E4-0141-199
Malfunction Troubleshooting (only by qualified staff)
Door fails to close/open completely. * - Uncouple the door and check the free running movement.
- When the door is uncoupled, does the drive unit carry out the
complete door stroke?
- Readjust the motor current limits by means of the BEDIS. Door movement is not reversed when it meets an obstacle during the
closing procedure.
Door is not stopped (motor is not switched off) if it meets an obstacle
during the opening procedure.
The drive unit cannot be activated by a transmit impulse, but it can
be actuated by means of a push-button or other pulse generators. - Replace the empty battery.
- Check the cable connections and the plug-in connections of the
receiver.
- Adapt the coding of the transmitter and the receiver according to
the F7000 instructions.
- Check if there is a voltage of 230 V at the plug socket.
- If necessary switch the main fuse on again.
- In the event of loose cable connections resp. defective miniature
fuses: pull out the power plug and restore the connections,
replace any defective miniature fuses 2 AT.
- Replace the the empty battery.
- Proceed to a correction of the receiver's location. Insufficient range of the remote control.
Drive unit can be actuated neither by a transmitter impulse nor by
any other control elements.
Troubleshooting instructions
* This malfunction can possibly be eliminated by pressing the RESET key.