Gilera SMT RCR 633793 Скачать руководство пользователя страница 93

Страница: 93 / 118

Rear brake calliper

Rear brake calliper replacement

- Support the scooter rear carriage axle adequate-

ly so that the rear wheel does not touch the ground.

- Detach the oil brake hose from the calliper, pour-

ing the fluid inside a container.

- Remove the wheel axle operating on the nut in-

dicated in the photograph.

- Upon refitting, tighten the wheel axle nut to the

specified torque.

- Purge the system.

Locking torques (N*m)

Wheel axle nut

70 ÷ 80 Nm

Front brake calliper

- Detach the oil brake pipe from the calliper; pour

the fluid inside a container.

- Remove the mountings indicated in the figure.

- When refitting, tighten the nuts to the prescribed

torque.

- Purge the system.

Locking torques (N*m)

Fixing screws

17 ÷ 19 Nm

Rear brake disc

Rear brake disc replacement

- Support the scooter rear carriage axle adequate-

ly so that the rear wheel does not touch the ground.

- Remove the rear wheel operating on the axle nut

indicated in the photograph.

- Undo the three disc clamps.

- Upon refitting, position the disc correctly making

sure that it rotates in the right direction.

Locking torques (N*m)

Wheel axle nut

70 ÷ 80 Nm

Rear brake disc

17 ÷ 19

Nm *

SMT RCR

Braking system

BRAK SYS - 93

Содержание SMT RCR 633793























































































































Результаты поиска

Содержание SMT RCR 633793

Отзывы:

Бренды по названию

Популярные бренды

Gilera SMT RCR 633793, Руководство по обслуживанию станции

Результаты поиска

Содержание SMT RCR 633793

Отзывы:

Бренды по названию

Популярные бренды