Gilera SMT RCR 633793 Скачать руководство пользователя страница 70

Страница: 70 / 118

- Thoroughly clean and degrease all the gearbox

components, the selector and the shaft with a de-

greasing agent

- Refit the secondary shaft making sure all com-

ponents are fitted correctly

- Refit the gearbox unit in the crankcase (the main

and the secondary shafts must be fitted at the

same time)

- First check the overall size of the secondary shaft

including shim washers. Overall size of the sec-

ondary shaft: Max. 87,700 mm. MIN. 87.350 mm

- Fit the selector. Lubricate the surfaces with spe-

cific oil

- Make sure that the gearbox works properly by

selecting different speed ratios and turning the

gear selector drum to both sides

- Select neutral gear and check that the system

rotates freely

- Refit the crankcase by warming up the shaft

seats at about 60°

- Tighten the screws to the prescribed torque

- Make sure the crankshaft and the gear rotate

freely after refitting the crankcase

Recommended products

AGIP CITY HI TEC 4T

oil to lubricate flexible

transmissions (throttle control)

Oil for 4-stroke engines

Locking torques (N*m)

Tightening torque:

6 Nm

Removing the clutch

Engine

SMT RCR

ENG - 70

Содержание SMT RCR 633793























































































































Результаты поиска

Содержание SMT RCR 633793

Отзывы:

Бренды по названию

Популярные бренды

Gilera SMT RCR 633793, Руководство по обслуживанию станции

Результаты поиска

Содержание SMT RCR 633793

Отзывы:

Бренды по названию

Популярные бренды