manualshive.com logo in svg

Gilera SMT RCR 633793, Руководство по обслуживанию станции

Поделиться
Скачать
Gilera SMT RCR 633793 Скачать руководство пользователя страница 28

CAUTION

ONLY USE DOT 4-CLASSIFIED BRAKE FLUID.

IN NORMAL CLIMATIC CONDITIONS IT IS ADVISABLE TO
REPLACE THE ABOVE MENTIONED FLUID EVERY 2
YEAR.

Recommended products

AGIP GP 330

 

Grease for brake levers, throttle

White calcium complex soap-based spray grease

with NLGI 2; ISO-L-XBCIB2

Headlight adjustment

- Position the scooter with rider on a flat ground, 10 m away from a half-lit white screen.

- Make sure that the scooter axle is perpendicular to the screen.

- Measure the height from the centre of the headlight to the ground and then mark a cross on the wall

at the same height measured.

- Start the engine and lock the throttle at 1/3 of its stroke.

- Turn on the low-beam light, the maximum demarcation limit between the dark and the light area must

be at a height not exceeding 8/10 of the height from the ground to the centre of the headlight.

Maintenance

SMT RCR

MAIN - 28

Содержание SMT RCR 633793























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды