Gilera SMT RCR 633793 Скачать руководство пользователя страница 24

Страница: 24 / 118

Air filter

- To reach the filtering element, remove the saddle

and the right side fairing.

- Afterwards, remove the 4 screws on the air filter

cover shown in the photograph.

Cleaning

- Wash the sponge with water and mild soap.

- Dry it with a clean cloth and short blasts of com-

pressed air.

- Soak the sponge in a solution of 50% petrol and

50% SELENIA AIR FILTER OIL.

- Gently squeeze the filtering element with your

hands without wringing it; let it drip dry and then

refit.

CAUTION

NEVER RUN THE ENGINE WITHOUT THE AIR FILTER,
THIS WOULD RESULT IN AN EXCESSIVE WEAR OF THE
PISTON AND CYLINDER.

transmissions

Transmission adjustment

- Adjust the control cables:

- Mix cable: see "Mixer timing" section.

- Throttle cable: adjust it in such a way that the sheath does not have any clearance.

- Splitter control cable: Adjust it in such a way that there is no clearance on the throttle grip.

- Adjust all transmissions in such a way that their sheaths do not have any clearance.

Mixer Timing

Maintenance

SMT RCR

MAIN - 24

Содержание SMT RCR 633793























































































































Результаты поиска

Содержание SMT RCR 633793

Отзывы:

Бренды по названию

Популярные бренды

Gilera SMT RCR 633793, Руководство по обслуживанию станции

Результаты поиска

Содержание SMT RCR 633793

Отзывы:

Бренды по названию

Популярные бренды