Gilera SMT RCR 633793 Скачать руководство пользователя страница 73

Страница: 73 / 118

Visually inspect in between the teeth. Replace the

component if there are signs of thermal fatigue,

reduced surface hardness or teeth irregular wear.

Check the components of the clutch bell are in

good conditions:

- Clutch disc seats

- Rivets and connecting plugs with crown gears

- Main shaft lever coupling

CAUTION

REPLACE THE PART IN CASE OF EXCESSIVE
DAMAGE.

Check that the coupling between the surface and

the plate is not eroded or grooved. Replace the

part if any defect is found.

CAUTION

REPLACE THE PART IN CASE OF EXCESSIVE
DAMAGE.

Check the pressure disc and its axial bearing.

CAUTION

REPLACE THE PART IN CASE OF EXCESSIVE
DAMAGE.

Pinion fitting

- Insert the wrench in the crankshaft and then fit

the main transmission gear

- Fit the hydraulic pump and the oil pump driving

gear

- Lock the magneto flywheel with the aid of the

specific tool and tighten the main transmission

gear fixing nut and the pump driving gear fixing nut

Specific tooling

SMT RCR

Engine

ENG - 73

Содержание SMT RCR 633793























































































































Результаты поиска

Содержание SMT RCR 633793

Отзывы:

Бренды по названию

Популярные бренды

Gilera SMT RCR 633793, Руководство по обслуживанию станции

Результаты поиска

Содержание SMT RCR 633793

Отзывы:

Бренды по названию

Популярные бренды