manualshive.com logo in svg

Gilera SMT RCR 633793, Руководство по обслуживанию станции

Поделиться
Скачать
Gilera SMT RCR 633793 Скачать руководство пользователя страница 23

- With the engine at 3000 rpm, check that the line

(1) on the magneto flywheel is aligned with the

notch on the crankcase (2).

T

ECHNICAL

 

SPECIFICATIONS

Specification

Desc./Quantity

Timing

22º at 3000 rpm

Advance

1.8º at 3000 rpm

Spark plug

- Clean the deposits between the two electrodes.

- Clean off mud and dirt that may accumulate around the spark plug base.

- Remove the spark plug and make sure the electrodes are not worn. The central electrode must have

clean corners and the external electrode must have a regular thickness.

- Replace the spark plug if signs of wear are detected or the insulator is cracked or chipped.

- Check the electrode gap with a thickness gauges.

- The gap must be 0.6÷0.7 mm.

Electric characteristic

Spark plug

NGK B8 ES

- Fit the spark plug manually to avoid damaging

the thread, and tighten it slightly with the appropri-

ate wrench.

Locking torques (N*m)

Spark plug

 

20 ÷ 24

SMT RCR

Maintenance

MAIN - 23

Содержание SMT RCR 633793























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды