GILBARCO VEEDER-ROOT Encore 700 S Скачать руководство пользователя страница 15

Страница: 15 / 72

MDE-4902E Encore® 700 S Start-up and Service Manual · February 2018

Page 3-3

CRIND Mode

Start-up

Press

Enter

. The CRIND ID Side 1 screen is displayed. (see

Figure 3-4

Note: Each CRIND device is programmed separately by inserting the CRIND diagnostic card

on each side (cannot be done from the same side). The CRIND ID screen is called



“Side 1” irrespective of the side being programmed.

Figure 3-4: CRIND ID Side 1

CRIND ID Side 1

CRIND ID 1
(Range: 1 - 32, 99 = disable)

Number Keys = Direct Entry
Clear = Erase Entry
Enter = Save Value and Exit
Cancel = Discard Change and Exit

The current CRIND communication
address for side 1.

Press numeric keys to enter one-digit or two-digit CRIND ID. To enter a two-digit CRIND ID,
for example, 32, press

Enter

and

Enter

. Legal values for this field are 1-32 and 99.

Setting the value as 99 configures the side not to answer polls on the CRIND communication
loop. This is useful for field troubleshooting and diagnostic purposes.

Press

Enter

to save the edited CRIND ID and exit. The CRIND IDs menu is displayed.

~ OR ~

Press

Cancel

to discard changes and exit. The program returns to the CRIND IDs menu.

CRIND Mode

To configure the CRIND Mode, proceed as follows:

From the CRIND Config menu, press

Enter

. The CRIND Mode menu is displayed.

Figure 3-5: CRIND Mode

CRIND Mode

CRIND Mode MOC
1. MOC
2. Generic

Enter = Save Value and Exit
Cancel = Discard Change and Exit

Shows current setting. For new
installations or CRIND devices that have
undergone a purge or BIOS coldstart,
default will not be configured.



Содержание Encore 700 S









































































Результаты поиска

Содержание Encore 700 S

Отзывы:

Похожие инструкции для Encore 700 S

Бренды по названию

Популярные бренды

GILBARCO VEEDER-ROOT Encore 700 S, Руководство по запуску и обслуживанию

Результаты поиска

Содержание Encore 700 S

Отзывы:

Похожие инструкции для Encore 700 S

Бренды по названию

Популярные бренды