Gigabyte TO22-Z61 Скачать руководство пользователя страница 55

Страница: 55 / 141

- 55 -

BIOS Setup

iSCSI Parameters via DHCP

Acquires the iSCSI parameters via DHCP.

Options available: Enabled/Disabled. Default setting is

Enabled

CHAP Authentication

Enable/Disable the CHAP authentication.

Options available: Enabled/Disabled. Default setting is

Disabled

Boot to Target

Enable/Disable booting to iSCSI target after log-on.

Options available: Disabled/Enabled/One Time Disabled. Default setting is

Enabled

DHCP Vendor ID

Press [Enter] to configures the DHCP vendor ID (up to 32 bytes long).

Link Up Delay Time

Configures the link up to delay time in seconds (0..225).

Use TCP Timestamp

Enable/Disable the TCP timestamp.

Options available: Enabled/Disabled. Default setting is

Disabled

Target as first HDD

Enable/Disable target appears as a first hard disk drive (HDD) in the system.

Options available: Enabled/Disabled. Default setting is

Disabled

LUN Busy Retry Count

Configures the number of retries in 2 second intervals when LUN is busy (0..60).

Default setting is

IP Version

Displays the IP version supported. Modifying this parameter will reset all IP-related fields.

Содержание TO22-Z61














































































































































Результаты поиска

Содержание TO22-Z61

Отзывы:

Похожие инструкции для TO22-Z61

Бренды по названию

Популярные бренды

Gigabyte TO22-Z61, Руководство пользователя

Результаты поиска

Содержание TO22-Z61

Отзывы:

Похожие инструкции для TO22-Z61

Бренды по названию

Популярные бренды