Gigabyte TO22-Z61 Скачать руководство пользователя страница 115

Страница: 115 / 141

- 115 -

BIOS Setup

5-7

Boot Menu

The Boot menu allows you to set the drive priority during system boot-up. BIOS setup will display an error

message if the legacy drive(s) specified is not bootable.

Boot Configuration

Setup Prompt Timeout

Number of seconds to wait for setup activation key. 65535 (0xFFFF) means indefinite waiting.

Press the numeric keys to input the desired values.

Bootup NumLock State

Enable/Disable the Bootup NumLock function.

Options available: On/Off. Default setting is

Full Screen LOGO Show

Enable/Disable the Full Screen Logo Show option.

Options available: Enabled/Disabled. Default setting is

Enabled

New Boot Option Policy

Controls the placement of newly detected UEFI boot options.

Options available: Default/Place First/Place Last. Default setting is

Default

Boot mode select

Selects the boot mode.

Options available: LEGACY/UEFI. Default setting is

UEFI

Содержание TO22-Z61














































































































































Результаты поиска

Содержание TO22-Z61

Отзывы:

Похожие инструкции для TO22-Z61

Бренды по названию

Популярные бренды

Gigabyte TO22-Z61, Руководство пользователя

Результаты поиска

Содержание TO22-Z61

Отзывы:

Похожие инструкции для TO22-Z61

Бренды по названию

Популярные бренды