Gigabyte TO22-Z61 Скачать руководство пользователя страница 65

Страница: 65 / 141

- 65 -

BIOS Setup

5-2-6

USB Configuration

USB Controllers:

Displays the supported USB controllers.

USB Devices:

Displays the USB devices connected to the system.

Legacy USB Support

Enable/disable the Legacy USB support fuction. AUTO option disables legacy support if no USB devices
are connected. DISABLE option will keep USB devices available only for EFI applications.

Options available: Enabled/Disabled/Auto. Default setting is

Enabled

XHCI Hand-off

This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be
claimed by XHCI driver.

Options available: Enabled/Disabled. Default setting is

Enabled

USB Mass Storage Driver Support

(Note)

Enable/Disable the USB Mass Storage Driver Support.

Options available: Enabled/Disabled. Default setting is

Enabled

Port 60/64 Emulation

Enables the I/O port 60h/64h emulation support. This should be enabled for the complete USB Keyboard
Legacy support for non-USB aware OSes.

Options available: Enabled/Disabled. Default setting is

Enabled

USB hardware delays and time-outs:

USB transfer time-out

The time-out value for Control, Bulk, and Interrupt transfers.

Options available: 1 sec/5 sec/10 sec/20 sec. Default setting is

20 sec

(Note) This item is present only if you attach USB devices.

Содержание TO22-Z61














































































































































Результаты поиска

Содержание TO22-Z61

Отзывы:

Бренды по названию

Популярные бренды

Gigabyte TO22-Z61, Руководство пользователя

Результаты поиска

Содержание TO22-Z61

Отзывы:

Бренды по названию

Популярные бренды