Gigabyte G492-Z52 Скачать руководство пользователя страница 94

Страница: 94 / 137

- 94 -

BIOS Setup

5-3-3-1-1

DRAM Controller Configuration

Parameter

Description

DRAM Controller Configuration

DRAM Power Options

Press [Enter] to configure DRAM Power Options.

Power Down Enable

– Enable/Disable DDR power down mode.

– Options available: Auto, Enabled, Disabled. Default setting is

Auto

Power Down Entry Delay

–

Specifies the value.

SubUrgRefLowerBound

–

Specifies the value. Valid value: 6~1.

UrgRefLimit

–

Specifies the value. Valid value: 6~1.

DRAM Maximum Activate Count

– Options available: Untested MAC, 700K, 600K, 500K, 400K, 300K,

200K, Unlimited MAC, Auto. Default setting is

Auto

DRAM Refresh Rate

– Options available: 7.8 usec, 3.9 usec. Default setting is

Auto

Self-Refresh Exit Staggering

– Options available: Disabled, Trfc/3, Trfc/4. Default setting is

Disabled

Cmd2T

Selects the Cmd2T mode on ADDR/CMD.
Options available: Auto, 1T, 2T. Default setting is

Auto

Gear Down Mode

Enable/Disable the Gear Down Mode function.
Options available: Auto, Enabled, Disabled. Default setting is

Auto

Содержание G492-Z52










































































































































Результаты поиска

Содержание G492-Z52

Отзывы:

Gigabyte G492-Z52, Руководство пользователя, Страница: 94 / 137

Результаты поиска

Содержание G492-Z52

Отзывы: