Gigabyte G492-Z52 Скачать руководство пользователя страница 31

Страница: 31 / 137

- 31 -

System Hardware Installation

3-6 Installing the Mezzanine Card

Before you install/remove the mezzanine card:
• Make sure the system is not turned on or connected to AC power.
• Disconnect all necessary cable connections. Failure to observe these warnings could result in

personal injury or damage to the equipment.

3-6-1 OCP 3.0

Use of the following type of OCP 3.0 NIC is recommended:
• OCP 3.0 SFF with Pull Tab
• OCP 3.0 SFF with Ejector Latch

Follow these instructions to install an OCP 3.0 mezzanine card:

1. Remove the two screws securing the mezzanine card slot cover.

2. Remove the slot cover from the system.

Insert the OCP 3.0 mezzanine card into the card slot ensuring that the card is firmly connected to

the connector on the motherboard.

4. Tighten the thumbnail screw to secure the OCP 3.0 mezzanine card in place.

5. Reverse steps 3-4 to replace the OCP 3.0 mezzanine card.

Содержание G492-Z52










































































































































Результаты поиска

Содержание G492-Z52

Отзывы:

Gigabyte G492-Z52, Руководство пользователя, Страница: 31 / 137

Результаты поиска

Содержание G492-Z52

Отзывы: