Gigabyte G492-Z52 Скачать руководство пользователя страница 11

Страница: 11 / 137

- 11 -

Hardware Installation

1-2

Product Specifications

Soc

ket

Socket

Sec

uri

Security

System
Dimension

448 x 176 x 880 (W x H x D, mm)

Soc

ket

Socket

Sec

uri

Security

CPU

AMD EPYC™ 7003 series processor family

Dual processors, 7nm

Up to 64-core, 128 threads per processor

cTDP up to 280W

Compatible with AMD EPYC™ 7002 series processor family

NOTE: If only 1 CPU is installed, some PCIe or memory functions might be
unavailable

Soc

ket

Socket

Sec

uri

Security

Chipset

System on Chip

Soc

ket

Socket

Sec

uri

Security

Memory

32 x DIMM slots

DDR4 memory supported only

8-channel memory architecture per processor

RDIMM modules up to 128GB supported

LRDIMM modules up to 128GB supported

3DS RDIMM/LRDIMM modules up to 256GB supported

1.2V modules: 3200*/2933 MHz

- Note:
* Follow BIOS setting and memory QVL list if running 3200 Mhz with 2DPC

Soc

ket

Socket

Sec

uri

Security

LAN

2 x 1Gb/s LAN ports (Intel® I350-AM2)

1 x 10/100/1000 management LAN

Soc

ket

Socket

Sec

uri

Security

Video

Integrated in Aspeed® AST2600

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp, DDR4 SDRAM

Soc

ket

Socket

Sec

uri

Security

Storage

12 x 3.5" or 2.5" hot-swappable HDD/SSD bays
- 4 x green HDD trays compatible with NVMe devices
- 4 x green HDD trays compatible with NVMe or SATA/SAS devices
- 4 x blue HDD trays compatible with SATA/SAS devices

SAS card is required for SAS devices support

Soc

ket

Socket

Sec

uri

Security

RAID

In option

NOTE:

We reserve the right to make any changes to the product specifications and product-related

information without prior notice.

Содержание G492-Z52










































































































































Результаты поиска

Содержание G492-Z52

Отзывы:

Gigabyte G492-Z52, Руководство пользователя, Страница: 11 / 137

Результаты поиска

Содержание G492-Z52

Отзывы: