manualshive.com logo in svg

Gigabyte G492-Z52, Руководство пользователя, Страница: 19 / 137

Поделиться
Скачать
Gigabyte G492-Z52 Скачать руководство пользователя страница 19

- 19 -

System Appearance

BMC : AUTH fail after doing recovery

(Note3)

Blinks Blue 
2 times per 
second
[ON OFF OFF]

Blinks Green 
2 times per 
second
[ON OFF OFF]

BIOS : AUTH fail after doing recovery

(Note3)

Blinks Blue 
2 times per 
second
[ON OFF OFF]

Blinks Amber 
2 times per 
second
[ON OFF OFF]

Backup Flash Authentication Fail

(Note4)

BMC : AUTH fail

Blinks Blue 
2 times per 
second
[ON OFF 
ON OFF]

Blinks Green 
2 times per 
second
[ON OFF 
ON OFF]

BIOS : AUTH fail

Blinks Blue 
2 times per 
second
[ON OFF 
ON OFF]

Blinks Amber 
2 times per 
second
[ON OFF 
ON OFF]

NOTE!
1.  EC FW is broken or not exited result in Microchip CEC1702 cannot load EC FW for authentication.
2  (1)  Authentication fail include below scenarios

 

Configuration table is missing or modified

 

Public key is missing or modified

 

Protected area or signature is modified

 

Flash empty

3.  If active flash is still authentication failed after recovery sequence, Microchip CEC1702 stop the process 

and showing LED behavior.

4.  If backup flash authentication is failed cause by configuration table, public key or protected area is 

broken. Microchip CEC1702 stop the process and showing LED behavior.

5.  Front panel LED is controlled by BMC or Microchip CEC1702. Once Microchip CEC1702 is working(Auth 

or recovery), the front panel LED is controlled by Microchip CEC1702 and vice versa.

Содержание G492-Z52










































































































































Отзывы:

Нет отзывов