GiBiDi TOP EVO 291E/S, Инструкция по установке

Страница: 30 / 60

UK
30 TOP EVO 31 TOP EVO
UK
10 OPERATOR INSTALLATION -
1 - Check the fixing point most suitable for the front bracket of the operator [5] and mark it.
2 - Indicate the point on the pillar with a spirit level to fix the rear bracket [5] .
3 - Find the fixing point of the rear bracket in function of quotas A-B [4] .
WARNING : if the pillars or walls are big, you must make a niche [7] , so that quotas A, B, E are met.
4 - Fix the rear bracket:
• Weld (if it is an iron pillar), previously checking the column thickness. If it is less than 5mm, provide a
reinforcing plate of such size that it allows making the welds on the edge of the column.
• If it is a concrete pillar, you must make a plate 5 mm of thickness with no. 4 holes. Weld the bracket in the
middle of the plate and fix it with some screws.
5 - Power the operator [9] , bring the rod completely forward, then make it go back for 5-10 mm .
6 - Fix the front bracket on the operator [8] .
7 - ring the leaf in closing position against the mechanical stops and fix it with a clamp.
8 - Mount the operator on the rear bracket with the pin provided [8] .
9 - Put the front bracket in the point previously marked at point 1, check the levelling of the operator with a spirit level
and mark the exact fixing point of the front bracket [5-6] .
10 - Remove the operator from the rear bracket.
11 - Remove the front bracket of the operator.
12 - Fix the front bracket in the point marked.
Fixing the front bracket:
• Weld (if it is an iron gate), previously checking the tubular thickness, where we are going to weld
the bracket. If it is less than 5mm, provide a reinforcing plate of such size that it allows making the welds
on the edge of the tubolar.
• If the gate is made with a material different from iron, you must make a plate 5 mm of thickness with no. 4 holes.
Weld the bracket in the middle of the plate and fix it with some through screws.
13 - Assemble the operator on the brackets [8] .
14 - Screw the tension rods [10]
15 - Lightly lubricate the seal [10], i nsert the carter [10] [10].
16 - Fix all with the two screws provided
Ã
[10] .
WARNING :
• Make the welding operations with the operator not assembled on the brackets.
• In case of heavy and/or buffered gates, it is necessary to strenghten both brackets with reinforcing hard metal
plates (not provided ).
• Before definitively fixing the brackets, make some manual tests of gate opening and closing, to check the
installation quotas.
À
for 4-5 mm on the operator head.
Ä Á
and the head
Â
12 THRUST ADJUSTMENT -
13 CONVERSION FROM IRREVERSIBLE TO REVERSIBLE OPERATOR -
11 MANUAL MANOEUVRE (UNLOCKING DEVICE) -
Unlocking device with hexagonal key [11]:
Turn the cover
À
and lift it, turn the unlocking key
Á
anti-clockwise by 2 turns and carry out the manual
manoeuvre.
To reset turn the key
Á
clockwise until it stops without forcing it, replace the cover into its original position.
Unlocking device with personalised key [12]:
Push the cover
Â
in the arrow direction, insert the key
À
in the cylinder
Á
, turn the key clockwise, turn the
unlocking key
Ã
anti-clockwise by 2 turns and carry out the manual manoeuvre.
To reset turn the key
Ã
clockwise until it stops without forcing it, turn the key
À
anti-clockwise, replace the cover
Â
into its original position.
WARNING: carry out the operations for the manual manoeuvre with the motor off.
[ ]
In order to increase the thrust, turn the valves
À
and
Á
clockwise with a screwdriver 13 ; in order to decrease
the thrust, turn the valves anti-clockwise.
In detail :
[ ]
• The valve
À
13 adjusts the OPENING thrust.
[ ] • The valve
Á
13 adjusts the CLOSING thrust.
WARNING:
When you adjust the thrust, turn the valves smoothly and gradually without unscrewing or
completely screwing them, keeping in mind that the operators are provided with the thrust already adjusted in
its best way during testing mode.
The operator is equipped with pressure control labels both for right and left version, already attached to the
motor.
TOP EVO operator is manufactured and sold as IRREVERSIBLE, if you need you can transform it into
reversible in opening or closing or both in opening and closing.
[ ]
The reversibility of the operator is controlled by the cursors
Â
and
Ã
13 , turning them clockwise until they are
blocked the operator is irreversible, turning them anti-clockwise the operator becomes reversible.
In detail with the operator installed on LEFT leaf:
[ ]
• The valve
Ã
13 controls the reversibility in OPENING.
[ ]
• The valve
Â
13 controls the reversibility in CLOSING.