manualshive.com logo in svg

Giant Factories InnoFlue Centrotherm, Руководство пользователя по установке и эксплуатации, Страница: 8 / 24

Поделиться
Скачать
Giant Factories InnoFlue Centrotherm Скачать руководство пользователя страница 8

8

Table 3 — DuraVent™

Appliance 

adapter

Increaser

Appliance 

adapter clamp

3-inch (7.6 cm) pipe

2PPS-AD 2PPS-X3

PPS-PAC

Through-the-Wall Venting Installation

DANGER

WARNING

CAUTION

AVERTISSEMENT

ATTENTION

When installing the vent piping, make sure that the vent 

terminal is 

NEVER

 installed below the air intake terminal. 

The air intake terminal must always face downward. Failure 

to follow this instruction could result in property damage, 

personal injury, or death.

Two (2) vent terminal options are available to vent this water 

heater. The first is a standard 90-degree elbow facing down-

ward 

(see Figure 6a)

 and the second is the concentric vent 

termination kit 

(see Figure 6b)

.

Cut or drill two (2) holes through the exterior wall, slightly larger 

than the diameter of the vent pipe selected. The larger holes will 

allow for final alignment with the water heater. Extend a section 

of pipe through each hole to the outside and attach the terminat-

ing elbow to the exterior end of each pipe. The vent and air intake 

terminals must be at least eight (8) inches (20.3 cm) apart and 

the vent terminal must 

NEVER

 be installed below the air intake 

terminal for any reason 

(see Figure 6a)

. The air intake terminal 

and the vent terminal must terminate on the same exterior wall 

(same atmospheric pressure zone).

The air intake equivalent vent length must be equal to or less 

than the exhaust equivalent vent length and the air intake ter-

mination elbow shall be equipped with a standard wire mesh 

screen. 

IMPORTANT

Connect and secure all piping and elbows from the power venter 

to the wall. When the installation is completed, the vent and air 

intake terminals must be at two (2) inches (5.1 cm) from the 

exterior surface of the wall 

(see Figure 2)

. Do not extend vent 

or air intake piping past this length. Make sure that all piping is 

properly supported. If the venting will pass through an enclosed 

area, make sure to leave at least one (1) inch (2.5 cm) clearance 

around the piping for air circulation.

FOR PVC AND CPVC PIPING: 

PolyPro

®

InnoFlue

®

Make sure that all horizontal runs have a minimum rise of 1/4 

inch per foot (21 mm/m) of run 

(see Figure 7)

. Horizontal 

runs of vent pipe must be supported every three (3) feet (91 

cm).

FOR POLYPROPYLENE PIPE FROM CENTROTHERM 

(Innoflue single wall vent system): 

PolyPro

®

InnoFlue

®

Make sure that all horizontal runs have a minimum rise of 5/8 

inch per foot (56 mm/m) of run. Follow instruction of the vent 

pipe manufacturer for proper vent support.

FOR POLYPROPYLENE PIPE FROM DURAVENT 

(Polypro single wall gas vent system): 

PolyPro

®

InnoFlue

®

Make sure that all horizontal runs have a minimum rise of 1/4 

inch per foot (21 mm/m) of run. Follow instruction of the vent 

pipe manufacturer for proper vent support.

Concentric Vent Termination Kit Installation

A three (3) inch (7.6 cm) Concentric Vent Termination Kit (IPEX 

model 196006) may be used with a three (3) inch (7.6 cm) 

restrictor screen for side wall termination installations. Using 

this Concentric Vent Termination Kit will reduce the maximum 

allowable equivalent vent pipe length for both air intake and 

exhaust systems 

(see Table 1)

. 

Figure 6b

 illustrates the 

Concentric Vent Termination Kit for side wall installation. See 

manufacturer’s instructions for complete installation details.

Through-the-Roof Venting Installation

Cut or drill two (2) holes through the roof and ceiling, slightly larg-

er than the diameter of the vent pipe selected. The larger holes will 

allow for final alignment with the water heater. Construct the vent 

terminal assembly. Extend a section of pipe through each hole in 

the roof to the outside and attach the terminal assembly to the 

exterior end of each pipe. The vent and air intake terminals must 

be at least eight (8) inches (20.3 cm) apart and the vent terminal 

INSTALLATION INSTRUCTIONS

Appliance adaptor

3” venting

3” venting

Increaser

Appliance adaptor

Vent System Adaptor

Appliance 

Adaptor Clamp

Increaser

Figure 4 

 — InnoFlue

® 

Centrotherm

Appliance adaptor

3” venting

3” venting

Increaser

Appliance adaptor

Vent System Adaptor

Appliance 

Adaptor Clamp

Increaser

Figure 5 

— PolyPro

® 

DuraVent

Содержание InnoFlue Centrotherm

























Отзывы:

Нет отзывов