GHM DeltaOhm HD402 Series Скачать руководство пользователя

Страница: 25 / 28

HD402…

- 25 -

V1.1

ACCESSORIES ORDERING CODES

Accessories included:

•

One piece of silicone tubing

∅

5 internal/

∅

8 external, length 2 m.

•

Two plastic fittings (HD434T.5).

AP3719

Flow port for square or cylindrical duct.

AP3721

Plastic flow port for cylindrical duct.

RS27

RS232 null-modem serial connection cable with SubD 9-pin connector on the PC
side and 3-pole connector on the instrument side.

CP27

Connection cable with built-in USB/RS232 converter. USB connector on the PC side
and 3-pole connector on the instrument side.

RS48

Cable for RS485 connection with built-in USB/RS485 converter. The cable has USB
connector for PC and 3 separate wires for the instruments.

Delta OHM metrology laboratories LAT N° 124 are ISO/IEC 17025 accredited by
ACCREDIA for Temperature, Humidity, Pressure, Photometry / Radiometry, Acoustics
and Air Velocity. They can supply calibration certificates for the accredited quantities.

Содержание DeltaOhm HD402 Series





























Результаты поиска

Содержание DeltaOhm HD402 Series

Отзывы:

Похожие инструкции для DeltaOhm HD402 Series

Бренды по названию

Популярные бренды

GHM DeltaOhm HD402 Series, Руководство по эксплуатации

Результаты поиска

Содержание DeltaOhm HD402 Series

Отзывы:

Похожие инструкции для DeltaOhm HD402 Series

Бренды по названию

Популярные бренды