GHM DeltaOhm HD402 Series Скачать руководство пользователя

Страница: 19 / 28

HD402…

- 19 -

V1.1

is set to OUTS.

•

Hysteresis

(HYST): Value of the hysteresis for above (RISE) and below (FALL)

threshold alarm operating modes. The parameter does appear if the alarm operat-
ing mode is set to OUTS.

•

Alarm activation delay

(T1): Value in seconds of the time delay for generating

the alarm. The alarm is generated only if the measurement exceeds the thresh-
old for more than the set time.

•

Alarm deactivation delay

(T2): Value in seconds of the time delay for deac-

tivating the alarm. The alarm is de-activated only after the set time has elapsed
from the disappearance of the alarm condition.

Note: the EDGE, THR1, THR2, HYST, T1 and T2 parameters do not appear if the alarm
is set to OFF.

Changing non-numerical parameters:

•

Select the parameter by using the button

•

Short press the button

to change the setting.

•

Long press the button

to move to the next parameter.

Changing numerical parameters:

•

Select the parameter by using the button

•

Short press the button

to change the sign.

•

Long press the button

to select the first digit.

•

Short press the button

to change the selected digit.

•

Long press the button

to select the next digit.

•

Repeat the above two steps until all the digits are set.

•

Long press the button

to move to the next parameter.

While a parameter value is displayed, a short press of the button

will briefly show

the name of the currently selected parameter.

4.4

RROR MESSAGES ON DISPLAY

Undr

: The measured value is less than the minimum measurable value.

OvEr

: The measured value exceeds the maximum measurable value.

CAL Error

: It appears at the end of the zero calibration if the maximum offset value

possible to be corrected is exceeded.

Содержание DeltaOhm HD402 Series





























Результаты поиска

Содержание DeltaOhm HD402 Series

Отзывы:

Похожие инструкции для DeltaOhm HD402 Series

Бренды по названию

Популярные бренды

GHM DeltaOhm HD402 Series, Руководство по эксплуатации

Результаты поиска

Содержание DeltaOhm HD402 Series

Отзывы:

Похожие инструкции для DeltaOhm HD402 Series

Бренды по названию

Популярные бренды