GHM DeltaOhm HD402 Series Скачать руководство пользователя | Manualshive

Страница: 20 / 28

background image

HD402…

- 20 -

V1.1

5

ALARM OPERATING MODES (HD402TR…)

Above threshold (RISE)

: the alarm is turned on if the measurement is greater than

threshold 1 for more than T1 seconds. The alarm is turned off when the measurement
becomes less then threshold 1 minus the hysteresis for more than T2 seconds.

The up arrow on the left of the display is shown when this mode is selected.

Below threshold (FALL)

: the alarm is turned on if the measurement is less than

threshold 1 for more than T1 seconds. The alarm is turned off when the measurement
becomes greater then threshold 1 plus the hysteresis for more than T2 seconds.

The down arrow on the left of the display is shown when this mode is selected.

Outside thresholds (OUTS)

: the alarm is turned on if the measurement is greater

than threshold 2 or less than threshold 1 for more than T1 seconds. The alarm is turned
off when the measurement returns between the two thresholds for more than T2 sec-
onds. No hysteresis is applied to the thresholds.

The up and down arrows on the left of the display are shown when this mode is se-
lected.

«
...
18
19
20
21
22
...
»

Содержание DeltaOhm HD402 Series





























Отзывы:

Нет отзывов

Похожие инструкции для DeltaOhm HD402 Series

Бренд: T-Drill Страницы: 75

Бренд: Zeiss Страницы: 38

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: Vahle Страницы: 96

Бренд: GALBIATI Страницы: 20

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Optima XR200amx

Бренд: GE Страницы: 46

Бренд: SAC Страницы: 2

Portable Vocal Booth Pro Studio Series

Бренд: EditorsKeys Страницы: 2

Calculite C6P38MHA

Бренд: Lightolier Страницы: 2

Бренд: Cooper Страницы: 10

Бренд: Korg Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды