GF Modbus RTU Скачать руководство пользователя

Страница: 7 / 16

Instruction manual

Place the Modbus RTU board into the free slot. Make sure that the
board is correctly snapped into the guide rails.

CAUTION

STATIC DISSIPATIVE

OBSERVE PRECAUTIONIS

FOR HANDLING

ELECTROSTATIC SENSITIVE

DEVICES

Insert the Modbus RTU connection cable into the cable union and
connect the glands D0, D1 and COM to the connector on the board.

The cable has to be secured against movement with the safety cap
fastenings.

Cable specification
Solid wire

26-16 AWG / 0.129-1.31 mm

Stranded wire

26-16 AWG / 0.129-1.31 mm

Torque

3.0 Lb-In / 0.34 Nm

Wire stripe length

6-7 mm

COM D0 D1

Set the termination-switch, located at the Modbus RTU board, to ON

•

for the last actuator in the Modbus network or

•

if there is only one actuator in the network

to activate the end termination.

OFF

Close the housing cover of the electric actuator by fixing the 4 Torx
screws.
Reconnect the power supply to power up.

Содержание Modbus RTU

















Результаты поиска

Содержание Modbus RTU

Отзывы:

Похожие инструкции для Modbus RTU

Бренды по названию

Популярные бренды

GF Modbus RTU, Инструкция по эксплуатации

Результаты поиска

Содержание Modbus RTU

Отзывы:

Похожие инструкции для Modbus RTU

Бренды по названию

Популярные бренды