GF Modbus RTU Скачать руководство пользователя

Страница: 12 / 16

Instruction manual

5.4.10 ACKRST

Control Byte to acknowledge error and reset cycle counter.

Byte-Name: ACKRST
Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Action

reserved

cycle_
cntr_reset

error_ack

reset_cycle_counter

error_ack

5.4.11 POSSET

The position setpoint is active if positioner mode is enabled, see register EACON.

Byte-Name: POSSET
Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Action

position_setpoint in percent 0…100%
active if positioner is enabled

0…100 = setpoint range
0 = closed position
100 = open position
101…255 = invalid value (no action)

5.4.12 BCDSET

This setting reproduces the functionality of the monitoring board hardware.
Note that the Bytes BCDSET0 and BCDSET1 are combined to the 16-Bit-Register BCDSET.

Word-Name: BCDSET

High Byte

Low Byte

BCDSET1

BCDSET0

The default value after factory reset is 0940(hex) respectively 2368.

Содержание Modbus RTU

















Результаты поиска

Содержание Modbus RTU

Отзывы:

Похожие инструкции для Modbus RTU

Бренды по названию

Популярные бренды

GF Modbus RTU, Инструкция по эксплуатации

Результаты поиска

Содержание Modbus RTU

Отзывы:

Похожие инструкции для Modbus RTU

Бренды по названию

Популярные бренды