manualshive.com logo in svg

GEZE Slimdrive SLT, Инструкция по установке и обслуживанию, Страница: 25 / 36

Поделиться
Скачать
GEZE Slimdrive SLT Скачать руководство пользователя страница 25

Slimdrive SLT product family

25

Production test and commissioning

6.2  Mounting the cover

WARNING! 

Risk of injury!

People can be injured when handling the cover.

 

X

Always make sure two people handle the cover.

WARNING! 

Risk of injury from falling cover!

 

X

Make sure that the cover is attached along the entire length of the track.

 

X

Release the cover carefully and check whether it has been suspended safely.

 

X

Unscrew the locking pin (1) from the tooth 

belt locking mechanism (optional).

6.3  Mounting the cover suspension piece

 

X

Insert the suspension pieces (1) for the cover catch cable into 

the front groove on the right approx. 1 cm from the edge of the 

track and on the left approx. 1 cm from the edge of the cap. 

 

X

Screw in using the enclosed fillister head tapping screws (2).

 

X

Make sure there is enough space for the earthing after installation of the suspension pieces (1) in the cover.

 

X

Push the suspension pieces (1) for the cover 

safety rope, right and left, approx. 5 cm from the 

edge of the cover on each side, into the groove 

(3) of the cover. 

 

X

Screw in using the enclosed fillister head tapping 

screws (2).

 

Содержание Slimdrive SLT





































Отзывы:

Нет отзывов