GEZE Slimdrive SLT Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

GEZE Slimdrive SLT Скачать руководство пользователя страница 17

Slimdrive SLT product family

17

Installation

5.4.5 Adjusting the moving leaves

WARNING

Risk of crushing!

The moving leaves are still unsecured and move easily.

X

Ensure that the moving leaves are not moved accidentally or by unauthorised persons!

X

Observe the applicable standards and guidelines on crushing, shearing and drawing-in spots.

X

Loosen the locknut (1).

Adjusting the inclination and level of the moving leaves

X

Adjust the inclination and level of the moving leaves using the hex of the suspension bolts (2):

Horizontal adjustment of the moving leaves

X

Move the moving leaves horizontally in the leaf suspension (3).

X

Make the individual moving leaf move smoothly.

X

Align moving leaves flush with each other. Ensure the same level and parallel closing edges when doing so.

X

Align moving leaves to maximum opening width.

Once all the moving leaves have been adjusted:

X

Tighten the lock nut (1) (torque 20 Nm).

«
...
15
16
17
18
19
...
»

Содержание Slimdrive SLT





































Отзывы:

Нет отзывов