Gewiss JOINON EASY GW68116 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 28

background image

27

The procedure for accessing the USB connector available in the charging stations is described below.
Open the enclosure door to access the device's USB socket-outlet and insert the USB memory in the relative
connector.
The charging station must be powered to load the data.
If the parameters were loaded successfully, the station signal will flash white for a few seconds.
After loading the data, remove the USB memory and close the enclosure door.

ACCESS AND DATA LOADING

16.

«
...
25
26
27
28
»

Содержание JOINON EASY GW68116





























Отзывы:

Нет отзывов

Похожие инструкции для JOINON EASY GW68116

Бренд: KC HiLiTES Страницы: 4

iVu Plus BCR Gen2 Series

Бренд: Banner Страницы: 12

Бренд: Banner Страницы: 28

Бренд: Banner Страницы: 155

Бренд: Banner Страницы: 64

Бренд: Banner Страницы: 8

Бренд: Banner Страницы: 2

Бренд: Banner Страницы: 8

Бренд: Banner Страницы: 12

Бренд: Rice Lake Страницы: 2

DGIPOD-4655 - DATASHEET FOR IPHONE

Бренд: I.SOUND Страницы: 1

Бренд: BTC Страницы: 8

Бренд: Volvo Страницы: 188

Бренд: ICP DAS USA Страницы: 4

PACCAR PACMOBILE 20

Бренд: DAF Страницы: 18

Бренд: Joy-it Страницы: 7

RGBW Rock Lights

Бренд: Lit Lightz Страницы: 3

Бренд: VPG Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды