Getac W130 Series Скачать руководство пользователя

Страница: 121 / 134

The brightness level might be too low. Increase brightness by pressing

The display output might be set to an external monitor. To switch the

display back to the LCD, press

Reset the computer by pressing the

Ctrl

Alt

Del

keys if you are using

an external keyboard.

Try turning the computer off; wait a few seconds, then turn it backs

on.

The characters on the screen are dim.

Adjust the brightness.

Bad dots appear on the display at all times.

A small number of missing, discolored, or bright dots on the screen

    are an intrinsic characteristic of TFT LCD technology. It is not
    regarded as a LCD defect. The Inspection Standard generally agreed
    in the LCD industry allows a maximum of 8 pixels on a unit.

Term definition:

Bright dots

When the LCD screen is lighted, dots appear
bright at a dark area. Red/green/blue bright dots
also count.

Dark dots

When the LCD screen is lighted, dots appear black
at bright areas.

Distance between

defective dots

The minimum distance between two defective
dots.

Adjacent defective dots

Defective dots within a radius of 10 mm.

Resolution cannot be adjusted to desired setting.

Make sure that the video driver is installed correctly.

Make sure that the video memory in the SCU program is configured

properly.

If using an external display device, make sure that the device supports

the desired resolution.

Troubleshooting

8-6

Содержание W130 Series







































































































































Результаты поиска

Содержание W130 Series

Отзывы:

Похожие инструкции для W130 Series

Бренды по названию

Популярные бренды

Getac W130 Series, Руководство оператора

Результаты поиска

Содержание W130 Series

Отзывы:

Похожие инструкции для W130 Series

Бренды по названию

Популярные бренды