Gesan DPR 100 Скачать руководство пользователя

Страница: 36 / 80

RENTAL & SILENT ENERGY RENTAL GENSETS 4.3

INCIDENT

DESCRIPTION OF ELECTRICAL TRIPS

ALARM
Electrical trip
Generator over current

Generator set current above electrical trip setting.

ALARM
Electrical trip
Auxiliary inputs

Auxiliary inputs can be configured and will display the message as
written by the user

ALARM
Electrical trip
kW overload

The total kW is above electrical trip setting.

ALARM
Electrical trip
Earth fault

The earth fault current is above electrical trip settings (only under
customer request)

ALARM
Electrical trip
Negative phase sequence

Indicates “out of balance” current loading of the generator set.

Note: Electrical trips are latching and stop the generator set but in a controlled manner. Firstly de-energize the “close
generator” output to remove the load from the generator set, and later, cool down and shutdown the unit.

Typical LCD Display Screens

Indicates that the generator set will respond to either a

mains failure or an active remote start.

Indicates that generator set is in automatic mode and has

been initiated after a mains failure has been detected.

Indicates generator set running normally in automatic

mode. Also indicates the average line to neutral voltage (L-

N), the highest of the three phase currents, the rated

frequency, average line-to-line voltage (L-L) and total kilowatts.



Measurement Parameter Display Screens:

Coolant temperature in degrees (ºC) Celsius and

degrees Fahrenheit (ºF)

Displays engine oil pressure in Bar, PSI and kPa.

All three generator line currents.

Содержание DPR 100

















































































Результаты поиска

Содержание DPR 100

Отзывы:

Похожие инструкции для DPR 100

Бренды по названию

Популярные бренды

Gesan DPR 100, Руководство пользователя

Результаты поиска

Содержание DPR 100

Отзывы:

Похожие инструкции для DPR 100

Бренды по названию

Популярные бренды