Geo BJ 120 Скачать руководство пользователя страница 4

 

 

 

 

 

GENERAL INFORMATION

 

 

 

 

 

 

 

Information about the manual

 

 

 

 

The using prescriptions shown in this handbook must be carefully observed to obtain the 

best  performances,  to  assure  the  greatest  duration  of  the  different  parts  and  to  avoid 
damages to the machine and accidents to the operator. lt is advised the careful reading of 
the present handbook, to deepen the knowledge of the MOWER BAR, before starting to use 
it. 

 

The present manual is to be considered an integral part of the machine, it must go with the 

machine in case of resale and till its demolition. 

 

Some illustrations in this manual show particulars or accessories that could be different from 

those of your machine, some component could have been removed to assure the clearness 
of the illustrations. 

 

The   subjects   dealt   in   this   handbook   are   those   expressly   requested   by   the 

"CE/98/37directive" and by the relatives technical standards. 

 

On  the  machine  are  inserted  apposite  pictograms,  which  the  operator  will  take  care  to 

maintain in perfect visual state and to replace when they are not more readable. 

 

 

 

 

  

 

 

 

 

This Handbook has been written following the effective regulations at the moment

 

of 

its printing. It is an integral part of the machine and must go with the machine with the 
Declaration of Conformity in case of resale.

 

 

 

 

 
 
 
 
 
 
 
 

Содержание BJ 120








































Отзывы: