Geo BJ 120 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 39

Geo BJ 120 Скачать руководство пользователя страница 35

35

safety signs are affixed to the implement and tractor. If any part of the operation and safe use of this
equipment is not completely understood, consult an authorized dealer for a complete explanation.

If the operator cannot read the manuals for themselves or does not completely understand the operation

of the equipment, it is not the responsibility of we to read and explain the manuals, safety practices, and
operating instructions to the operator, but operator itself.

Safe operation of equipment requires that the operator wear approved Personal Protective Equipment

(PPE) for the job conditions when attaching, operating, servicing, and repairing the equipment. PPE is
designed to provide operator protection and includes the following safety wear:

PERSONAL PROTECTIVE EQUIPMENT (PPE)

• Protective Eye Glasses, Goggles, or Face
Shield
• Hard Hat
• Steel Toe Safety Footwear
• Gloves
• Hearing Protection
• Close Fitting Clothing
• Respirator or Filter Mask (depends on

operating conditions)

4 INCONVENIENCES AND REMEDIES

INCONVENI

ENCES

CAUSE

REMEDY

Clogging of

hammers/k
nifes

Rotor speed

is too low

Increase

rotor speed

Excessive

wear of
hammers/k
nives

Rotor speed

is too high

Decrease

rotor speed

Shredder

vibrates
during
works



Foreign matter stuck in
between
knives broken



Bolts of the rotor shaft
support have come lose



Remove foreign matter



Replace knives



Lock bolts

«
...
33
34
35
36
37
...
»

Содержание BJ 120








































Отзывы:

Нет отзывов