Gentex HGU-55/P Скачать руководство пользователя страница 24

Страница: 24 / 70

Chapter 2: Helmet Preparation and Operation

11. Referring to

Figure 2-20

, do the following:

a. Insert the screws through the lock washers and the backing plate in that order.

b. On the inside of the helmet, position the backing plate against holes; insert the screws

through the holes.

c. On the outside of the helmet, position the spacer and the receiver over the screws with

the projections pointed toward the helmet rear. Ensure that the numbered side of the

receiver faces the helmet. Tighten the screws into the spacer and receiver.

d. Repeat Steps a-c on the other side of the helmet.

12. Apply a thin, even coat of polychloroprene adhesive to both the inside surface of the

helmet shell earcup areas and the back of the earcup pile fastener material. Do not

allow the adhesive to contact the backing plates, the screws, or the retention assembly

hardware. Allow the adhesive to dry approximately two minutes or until tacky.

13.

Press the earcup pile fastener material firmly against

the shell surface. Allow the adhesive to set at least 15

minutes; ideally, you should allow it to set overnight.

14. Use a utility knife to cut an "X" pattern through

the pile fastener over each screw head. This will

facilitate inspection, tightening, or replacement of the

hardware.

15. Reinstall the earcups and the visor.

16. Have the aircrew member don the helmet. Re-check

the helmet fit as described in Paragraph 2-2.3 and

make any needed adjustments.

17. Have the aircrew member don the mask. Check the

mask for proper position and tension in accordance

with applicable oxygen mask technical orders. Check

the interface between the visor and the mask. Adjust

the mask straps as required.

18. Connect the mask cord to the helmet connector

(

Figure 2-21

NOTE:

To remove the mask cord from the helmet

connector, pull firmly on the cord plug.

In Step 11, do not tighten either screw in the receiver until both screws have been started,

or you might cross-thread the receiver assembly.

CAUTION

Screws

Lock washers

Backing plate

Spacer

Bayonet receiver

Helmet

connector

Mask

cord

Figure 2-20. Installing Kit

Figure 2-21. Connecting Cord

Содержание HGU-55/P







































































Результаты поиска

Содержание HGU-55/P

Отзывы:

Похожие инструкции для HGU-55/P

Бренды по названию

Популярные бренды

Gentex HGU-55/P, Инструкция по эксплуатации и техническому обслуживанию с иллюстрированным перечнем деталей

Результаты поиска

Содержание HGU-55/P

Отзывы:

Похожие инструкции для HGU-55/P

Бренды по названию

Популярные бренды